EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 1
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 2
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 3
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 4
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 5
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 6
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 7
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 8
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 9
EagleTac T25C2 - Flashlights - Killzone Flashlights Hog, Predator and Varmint Hunting Flashlights - 10

EagleTac

EagleTac T25C2

$ 99.99

EagleTac T25C2 Black Tactical Flashlight with a maximum brightness of 1148 lumens.

 

What's included

Stainless steel bezel (removable)
Spare O-rings
Titanium coated Stainless steel pocket clip
User manual
Tail-stand rubber boot
Soft cigar holding grip
Cigar grip cover ring
Lanyard ring attachment ring
Heavy Duty Nylon Holster w/ self-retention device and flip
Mil-Spec Paracord Lanyard w/ quick attachment clip

 

High lumen output

LED lumen

  • XP-L HI V3: 1148-882/520/97/8

ANSI FL-12 lumen

  • XP-L HI V3: 992-764/450/87/7

Smart energy management

1) Energy saving feature (on by default) reduces lumen output by 24% after 200 seconds at turbo mode. With this feature turned off, turbo mode output lumen will be reduced by only 8% instead after 200 seconds. If you wish to turn off this feature, we recommend only do so when you are using 18650 batteries or more than two CR123A for better runtime.

2) ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured using a calibrated integrated sphere three minutes after turning on the flashlight.

 

 

Smart energy management
1) Energy saving feature (on by default) reduces lumen output by 24% after 200 seconds at turbo mode. With this feature turned off, turbo mode output lumen will be reduced by only 8% instead after 200 seconds. If you wish to turn off this feature, we recommend only do so when you are using 18650 batteries or more than two CR123A for better runtime.

2) ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured using a calibrated integrated sphere three minutes after turning on the flashlight.


Reflector

T25C2 uses polished aluminum reflector with smooth reflective finish for maximum output and far projecting beam. No donut, dark dot, or artifacts inside the beam.

T25C2 is without boundaries

Whether you're professionals that uses ultraviolet (UV) 365nm/395nm output for inspection/verification/curing, or specialists that uses infrared (IR) 850nm/940nm output for night vision purposes, or artists/perfectionists that uses high CRI, or hobbyists that uses multi-color LED for outdoor sport, the T25C2 offers a wide selections of optional LED drop-ins that comes in different wavelength and output to suit your special needs.

With improved LED efficiency and circuit performance introduced from LED or IC manufacturers almost every few years, always enjoy the latest technology and new functions by upgrading to the latest LED module at a very reasonable cost.

C3300 Extreme3

This highly efficient synchronous buck current regulated circuit controls the precious amount of current that goes through the LED at all output levels. This results in constant brightness output regardless of LED variation, battery voltage, and temperature change. The Low EMI management and quick soft-start design provide clean electricity for the circuit and LED to enhance their service life.

Our synchronous buck converter is more technologically advanced and compact than regular buck converter. It also allows more board space for our exceptionally low DCR mosfets, rugged & shielded power inductor, and low ESR tantalum capacitors. This together leads to very high efficiency and low dropout voltage which allows single 18650 to regulate at turbo for most of the runtime.


Excellent runtime and flat regulation

T25C2 runs for 150+ hours on its lowest brightness level with EAGTAC 3400mAh 18650 li-ion. The current regulated circuit design allows constant output throughout its runtime for all output levels without flicking.

At highest brightness level, T25C2 current regulates for 1 hour using two EAGTAC CR123A batteries. With two 3400mAh 18650 batteries (using 4 cells body extender) you get about 3.3 hours of runtime on high (2.5 hours with energy saving feature turned off).

The current regulation control method allows the just right of amount of current going through the LED. This results in constant brightness output regardless of battery type, LED variation, and temperature change.

Easy and Trusty operation

Switch on and off:
Turn on the light by pressing the tailcap button until it clicks. Slightly press for momentary on/off.

Switching between output

Twist the head to select between turbo, high, and medium output levels. You can pre-selected output level before turning on the light. To access the lowest level, switch to medium level (3rd level), then high level (2nd level), and then back to 3rd level within one second for the lowest output.

Cycle through auxiliary modes

Tighten the head (1st level), and loosen to 3rd level and then tighten the head within one second to enter auxiliary setting. Repeat to cycle through all settings. Turn off the light or loosen the head to quit.

Other powerful features

T25C2 comes with two pre-defined modes. i) Tactical mode which includes Hi/Lo brightness levels and a strobe output for tactical use; ii) Regular mode which includes four well separated brightness level for general use. To toggle between modes, dial to 2nd output level and turn the flashlight on and off for 20 times.

Tail strobe feature (off by default): With this enabled, you can access strobe output at the tailcap switch button . To enable (or disable) this function (disable from factory), dial to 1th level and turn the flashlight on and off 20 times (one second or less between each click). With the tailcap strobe setting enabled, double pressing the switch button (within one second) will activate the strobe output.

Energy saving feature (on by default): T25C2 reduces output by 24% after 200 seconds at turbo mode. With this feature turned off, turbo output will be reduced by only 9% after 200 seconds at turbo mode. To toggle this feature, dial the head to 3rd level and turn the flashlight on and off for 20 times. Once setting has been changed, LED will output 3 seconds at 100% (enable), or 1 second at 100% (disable).

Gorgeous knurling

T25C2 offers a sure grip with or without gloves. The body and the knurling surface are slightly polished by nylon wheels to give excellent gripping comfort.

Safety protection
Battery reverse polarity protection

Your safety is our first priority. Inserting battery in the wrong direction may lead to serious damage and fire. We incorporate a physical structure to protect against reverse polarity without compromise (battery with a protruding button top is required).

Battery stabilizer
We incorporate a spring loading mechanism in the flashlight body to prevent the batteries from rattling inside the body. This allows reliable battery contact regardless of head tighten or loosen.


Always ready for you

One press for MAX or MIN output
Unlike others that needs to cycle through modes or levels to get to the output you need. With head tighten/loosen, turning on the flashlight will always get you the maximum/minimum output power.

Four pre-defined output

Turn the head to access all three output levels. You can pre-select your desired output before turning on the light. For the lowest hidden output, start from head loose, tight and loose the head to enter the lowest output setting. This setting is especially useful when you are in a dark environment and need to preserve your adapted night vision.

WARRANTY


We (EAGTAC) warrant our flashlights to be free from defects in workmanship and materials. We will repair, replace at our option, without charging any product or part which is found to be defective under normal use within 120 months from the date of purchase with the proof of purchase.

Electronics, chargers and rechargeable batteries are covered for a period of 12 months with purchase receipt. Such repair or replacement shall be the purchaser’s sole and exclusive remedy under this warranty. Normal wear and tear including batteries draining is not covered, nor is damage resulting from modification, misuse, abuse, neglect, battery leakage, improper maintenance or repaired by anyone other than EAGTAC.

Customer Reviews

Based on 1 review Write a review